الترانزستور دارلنكتون (Darlington)
وهو عبارة عن ترانزستورين بغلاف واحد وفقط بثلاث أطراف خارجية ، ويمتاز بربح تيار علي (10000) ، وباستقرارية عالية ..
إن القيمة الفعالة لـ (hfe) أكبر بكثير من (hfe) لترانزستور واحد ولذلك نحصل على ربح تيار عالي ..
يتوفر هذا الترانزستور بالنوعين (D-npn) و(D-pnp) ..
يمكن الحصول على ترانزستور دارلنكتون من ترانزستورين ، وكمثال على ذلك :
- For TR1 use BC548B with hFE1 = 220.
For TR2 use BC639 with hFE2 = 40.
وبالتالي فإن الربح العام لهذا الترانزستور هو :
hfe = =hFE1 × hFE2 = 220 × 40 = 8800.
وإن استطاعة تيار الخرج الأعظمي للترانزستور الجديد هي نفسها تيار المجمع للترانزستور الثاني TR2 ..
إن حهد القاعدة اللازم لفتح هذا الترانزستور هو (0.7+0.7=1.4) ..
إن هذا الترانزستور يمكن أن يستخدم كمفتاح حساس جداً ، بما فيه الكفاية للاستجابة لتيار صغير جداً يمكن ان يكون ناتجاً عن ملمس الجلد البشري وكمثال عليه الدارة التالية (مفتاح يعمل بالمس):
المقاومة (100K) تحمي الترانزستور عن حصول تلامس مباشر مع منبع التغذية نتيجة قصر بسلك ..
- LED lights when the LDR is dark
Choosing a suitable NPN transistor :
-
- and choose the nearest standard value.The transistor’s maximum collector current IC(max) must be greater than the load current IC.
- The transistor’s minimum current gain hFE(min) must be at least five times the load current IC divided by the maximum output current from the chip.
- Choose a transistor which meets these requirements and make a note of its properties: IC(max) and hFE(min).
- Calculate an approximate value for the base resistor:
- The transistor’s minimum current gain hFE(min) must be at least five times the load current IC divided by the maximum output current from the chip.
- Finally, remember that if the load is a motor or relay coil a protection diode is required.
Example
The output from a 4000 series CMOS chip is required to operate a relay with a 100 coil.
The supply voltage is 6V and the chip can supply a maximum current of 5mA.- Load current = Vs/RL = 6/100 = 0.06A = 60mA, so transistor must have IC(max) > 60mA.
- The maximum current from the chip is 5mA, so transistor must have hFE(min) > 60 (5 × 60mA/5mA).
- Choose general purpose low power transistor BC182 with IC(max) = 100mA and hFE(min) = 100.
- RB = 0.2 × RL × hFE = 0.2 × 100 × 100 = 2000. so choose RB = 1k8 or 2k2.
- The relay coil requires a protection diode.
Choosing a suitable PNP transistor :
The procedure for choosing a suitable PNP transistor is exactly the same as that for an NPN transistor described above.
- and choose the nearest standard value.The transistor’s maximum collector current IC(max) must be greater than the load current IC.